Access Control Software&Cloud Security Intercom Network Audio&Video Integration Installation&Hardware Upgrade&Backup&Reset Other

Intercom

Description

Favorites

No description...

All
New
Highlight
Hot

New

New Window

Making a SIP or IP call by triggering the input on the doorphone panels

I use anything doorphone unit(Can be R20A,R27A,R28A,R26P .etc) I want to make call when I connected inputs of doorphone unit. How do I this solution? I want to talk about this post. Scenario: We have a R20A device and there are 2 input at ...

2021-11-01
2 1499

ercntrn

For example; You have a villa and you don't want to put a doorphone panel in your garden. Just imagine that you have a doorbell at your entrance. In order to call the staff inside your inside villa, you can call the staff inside when you press the button by just placing a button at the head of your ...

Reply
Push Button Action

Hi all, I have an issue w/ my new E12: When defining a 'Push Button Action' (Intercom -> Basic), that URL only seems to be executed whenever a SIP account is active. In general, that would be fine for me, if I at least could disable that ...

2022-02-10
9 1331

mnd

@CIE_Ash That does the trick, thanks!!

Reply
Speed Dial and Manager Dial

Speed dial and manager dial are used to quick initiate the pre-configured numbers by pressing Dial key. Firstly: You can enter the web interface of doorphone unit and enter the IP address of device to browser.To setup it on web Interc ...

2022-01-19
0 1258
Problem with "Call event" in R20A

After updating the firmware to version 220.30.3.2 I noticed that the call action (http url) after pressing the bell button on the panel no longer works. In the configuration of the panel : Intercom->Basic in the "Call Event" section, I have ...

2022-03-03
2 1246

Olgierd

Thank you very much for your answer. 1 Yes. The http command is correct. I tested it. I ran it in a web browser and it works fine, it triggers a ringtone in the Fibaro system. 2. Fibaro and Akuvox panel are in the same local network. 3. My configuration is presented below. I do not use Indoor Monit ...

Reply
R49G Guard Phone

I think most of us knew Akuvox begin from SIP phone, and produced the first Android phone, the first Android phone now have 2 generation, from R48 to R49. R48 and R49 have two UI suitable for different scenarios. Traditional UI used to de ...

2021-12-21
1 1215

Sandra

As a guard phone, R48 supports discovery mode and cloud mode, while R49 supports discovery mode, cloud mode and SDMC mode.

1 Reply
How to register sip server to akuvox doorphone, indoor monitor or guardphones?

To begin with, you should create users for the akuvoxdevices that you will use your project. After this process you should log inthe akuvox devices' web gui. At this point, you should click account>basic and fill out the part of register na ...

2022-02-16
0 1166
It is possible call the elevator that you without going out your from apartment

Hello, You can press the calling elevator button without going out youraparment. You can call the elevator button by using the relay of indoor monitors.Initially, you log in the web gui of indoor monitors and then click the part ofphone>re ...

2022-02-19
0 1160
How to setup Dial Plan:

Dial Planis used to create a dial plan.This feature is available in all apartment type doorphonepanel and IP phones. Most users want to use it. Because people want to calltheir flats with a shortcut.Forexample, when the person living in the ...

2022-01-19
0 1141
Adding Phonebook and Group to Doorphones

We can add a phone book to Akuvox outdoor devices via the webinterface.Firstly: You can enter the web interface of doorphone unit and enter theIP address of device to browser.To set upit on web PhoneBook > LocalBook web interface. 1)Contact ...

2022-01-17
0 1123
SIP and Polycome

I am new to Akuvox and learning more every day. I have R29s, R20A, and C319A. I have Polycom VWX 250 OBI sip phone working with google voice. Can I have a R29s make calls to the sip phone, when someone press the button for reception? A ...

2022-03-02
1 1108

ercntrn

Hi, Akuvox doorphones can working with SIP Server. If Polycom device can be register to SIP Server device It communication with Akuvox doorphone devices. How do you register to SIP Server device Akuvox doorphone.You can examine below forum information It helps to you. Link: http://community.akuv ...

Reply
How to Configure Auto Answer on Indoor Monitor

If you want your indoor monitor to answer automatically when a call is made from the doorphone, you can make the settings as in the picture. This feature is available in SIP and IP calling.Firstly: Please enter the indoor monitor's web inte ...

2022-05-05
0 1087
R20A Input Schedule

Hello, we have added a button in our garden to open the gate so that people with a car can get out easily. This will trigger Input A on the R20A, which will in turn open the gate with RelayA. However, security told me somebody could come ...

2022-07-13
3 1050

rumeysa

You're welcome

Reply
R20A call both SmartPlus APP and a SIP Phone

Hello, I would like to ask you if it is possible, using an R20A, to call both the SmartPlus App and a SIP Phone. I've tried registering the Account 1 with the cloud service and the Account 2 with our VoIP PBX. The call to the APP works fi ...

2022-08-01
5 1048

lebentech

Hi There, can you share an illustrative image of the example?

Reply
R20A call event without a call

Hello, i want to configure my R20A with a call event (http url) without a call. I have configured the Group call number with IP from the R20a itself. But here is a disturbing busy signal. I only want to do a http action when i push the but ...

2022-08-05
3 921

Jaaannis

Anyone has an idea for that? It is still a problem for me. Greetings

Reply
Akuvox C315W - I'm looking for a guide on how to connect a door lock

I'm looking for advice on how to connect the electric strike (Door Lock) directly to Akuvox. The last brown pin (NC) and the penultimate white pin (COM) come out of the Akuvox Monitor. Where and how to connect them and how to configure it i ...

2023-10-26
13 885

joschi

Hmm, the devil is in... simplicity Since I open the door on the call screen using the DTMF code of the remote relay (Auserwald TFS) and it is a local relay, it was necessary to simply, after correctly connecting the electric strike directly to the monitors, set the relay in the monitors in Softke ...

Reply
IT83 To IT83 Calling With Relay activation.

So not sure if anyone else has tried to do this particular set up before, if you have please feel free to advise me. So basically Calling IT83 to IT83 but i want the receiving IT83 local relay to activate on calling.

2022-08-16
1 868

CIE_Ash

Hi Ryan, This can be achieved by going to Phone -> Call Feature and enabling Local Relay1 Trigger by incoming or Local Relay2 Trigger by incoming.

1 Reply
R20A working SIP with Grandstream pbx

Hi, I've an r20a door phone in test with Grandstream pbx. I can't find info about this: I want to open the door using 1 relay and I've setup 4 digit dtmf "example: 1111". My question is, How can I activate the relay during a sip call, does ...

2022-09-11
4 862

alvaro.uy

Hi Ryan, yes I've tried different combinations like 99, 999, 9999, 7896, 8767, a lot of combinations. What I don't know is if I have to press any digit like *# or whatever After the dtmf digits.

Reply
R49G Device Bluetooth Configuration

R49G device has bluetooth feature.We can switch on the Bluetooth function on the device to establish the Bluetooth based connection with devices with the Bluetooth function for files transmission and making or answering the Bluetooth calls. ...

2022-07-22
0 822
open door with dtmf on incoming call on X915s doorbell

I can't open the door by a SIP call from my mobile to the X915s doorbell it works well when there is a call from doorbell to my mobile, but in other direction nothing happens How should I configure X915s to enable this?

2022-10-09
9 786

depaepe

any updates on this?

Reply
S563 and Google Play Store

Is it possible to install Google Play Store (and Google Play Services and Google Services Framework) on the S563 monitor? If I do this, does it mean the Google Play Store will work to download apps directly onto the S563? Thanks.

2024-08-01
6 766

stephen.davies

Can you repost the APK or publish it on the knowledge base The link has now expired.

Reply

12 3 4 5 / 5 PagesNext

Section statistics

Today
0
Threads
83
Posts
304

Hot labels